|
PICK
A DESIGN YOU PREFER FOR YOUR CHIMNEY.
Any of these styles will fit to your chimney.
Pick any style your
prefer for your chimney and click NEXT >>>
or the picture you like to go on the next page.
Some DOWNDRAFT PROBLEMS Reviewd
Rain Problems
& Vertical Wind Shift
Noisy
Flue & Pilot light
Wind Shadow
Downdraft
Cold Flue
You will have an option to chose metal type (stainless steel or copper) while
ordering.
This style is for single or insulated wall chimneys
with wall thickness less than 1".
Not for use with air cooled chimneys.
See
available stock sizes at the bottom of the page.
|
Picture |
Description |
Be
advised |
Fuel
Type |
NEXT >>>
|
RC
(Rain Cap).
The Rain Cap is designed for basic flue protection
against rain or snow, although it allows free flow of the smoke and
fumes. This model feature side screening, that keeps birds and animals out of the chimney and also keeps larger
sparks from exiting the chimney. Bolt down tops for easier cleaning. |
Wall thickness should not exceed 1 inch. Otherwise choose
round multi wall. |
Coal, Wood, Gas, Oil. |
NEXT >>> |
SR (SkyRider©). SkyRider
Cap turns its head depending on wind direction protecting your
chimney with front skirt and living open space at rear for easy
ventilation. As air moves over that cap, it creates low pressure of
air at the top of the chimney. That effect cures downdraft and
shifts residual fumes. SR is able to cure not severe
downdraft problems and provides rain protection. |
Wall thickness should not exceed 1 inch. Otherwise choose
round multi wall. |
Coal, Wood, Gas, Oil. |
NEXT >>>
|
DM
(DraftMaster© with a cone).
DraftMasters are specially designed to solve downdraft problems. It
will cure all downdraft problems that are cap related and most of
the problems that are not cap related. If tall trees or tall neighbor
house causes wind to change direction vertically and it get inside
of your flue to make downdraft, DraftMaster easily solves this type
of problem. This cap is stationary, no
moving parts inside. |
Wall thickness should not exceed 1 inch. Otherwise choose
round multi wall.
Mounting belt, securing the cap in its place, has to be
installed ~4" below top of the flue so installation require at least
4" of exposed flue length. |
Coal, Wood, Gas, Oil. |
NEXT >>>
|
AM (AirManager Cap©).
AirManager Cap is capable to cure downdraft problems that are cap
related. The way it is built, AirManager will not allow gusty movements
of air inside of the flue and it limits excessive updrafts providing
smooth air flow.
This cap is stationary, no moving parts
inside. |
Wall thickness should not exceed 1 inch. Otherwise choose
round multi wall.Mounting
belt, securing the cap in its place, has to be installed ~4" below top of
the flue so installation require at least 4" of exposed flue length.
|
Gas, Oil, other types of non heavy smoking fuels.
|
We sell only stock sizes online.
Check available stock sizes before you proceed. |
|
3" |
4" |
5" |
6" |
7" |
8" |
|
9" |
10" |
12" |
14" |
|
|
|
|
If you do not
see your chimney cap size in the table above,
e-mail us your size and we might make it as a custom order.
If the size or your chimney is significantly deviate from table sizes, email us picture or drawing of your chimney with dimensions
you think might interest us.
Should you have any questions, do not hesitate to
e-mail us. |
Phone 800-865-7603
FAX 800-865-7603 |
All dimensions provided in
inches. If you prefer metric system, divide your measurements by 25.4 for
millimeters (mm) or by 2.54 for centimeters (cm).
Example: you measured inside diameter of your chimney crown 152mm (15.2cm),
152mm/25.4=6in or 15.2cm/2.54=6in. |
|
|
|
to see quality of T304 brushed surface
stainless steel metal we use to make our caps, click on the picture
below.
SkyRider shaft Maintenance: Clean as needed
(once every 3 years recommended) and lubricate with a graphite
based lubricant. Do not use petroleum base grease.
|
|
|
